Views: 212 Author: Capital Technology Publish Time: 2026-11-20 Origin: Site
Content Menu
● Centrifugal Fan vs Axial Fan: Key Differences
● What Static Pressure Means for Equipment Cooling
● Why Centrifugal Fans Often Suit High Static Pressure
>> Where Centrifugal Fans Offer Practical Advantages
● When a High Static Pressure Axial Fan Can Be Better
>> Where High-Pressure Axial Fans Make Sense
● Compare Efficiency, Noise, and Ownership Cost Fairly
>> Efficiency and Electrical Requirements
● A Practical Fan-Selection Workflow
● Worked Selection Scenario: A Filtered Electronics Enclosure
● Select a Cooling Solution With CAPITAL
>> 1. Is a centrifugal fan always better for high static pressure?
>> 2. Can an axial fan cool equipment with dense heat sinks?
>> 3. Does higher maximum static pressure mean better cooling?
>> 4. Will two axial fans in series double the airflow?
>> 5. Can replacing a fan solve every overheating problem?
For most restrictive cooling systems, a centrifugal fan is the stronger starting point. However, the centrifugal fan vs axial fan comparison is not a universal ranking: high-performance axial designs, particularly counter-rotating fans, can also deliver substantial static pressure. The right choice depends on airflow at your actual operating pressure—not the largest number in a catalog.
At Capital Technology Co., Limited, our selection philosophy is straightforward: define the cooling requirement first, then compare suitable CAPITAL and SANYO DENKI solutions. Fan geometry matters, but the installed result matters more.

Axial fans move air approximately parallel to the motor shaft. Centrifugal fans draw air into an impeller and discharge it radially, turning the airflow approximately 90 degrees.
This difference influences pressure capability, packaging, and airflow routing.
| Selection factor | Centrifugal fan | Axial fan |
|---|---|---|
| Airflow direction | Turns radially from the inlet | Travels along the shaft |
| Typical strength | Restrictive airflow paths | High airflow through straight paths |
| Static pressure | Often advantageous against conventional axial designs | Highly dependent on design; counter-rotating models can be substantial |
| Installation | Requires space for radial discharge or a scroll outlet | Often suits panel mounting and straight-through layouts |
| Typical applications | Filtered equipment, heat exchangers, redirected cooling | Cabinets, electronics, server airflow channels |
| Efficiency and noise | Must be evaluated at the required duty point | Must be evaluated at the same duty point |
| Main selection risk | Blocking the discharge or disturbing the inlet | Selecting by free-air airflow despite system resistance |
Neither category is automatically quieter, more efficient, or smaller once the complete installation is considered.
Static-pressure capability helps a fan overcome resistance from filters, heat sinks, grilles, and internal components.
A fan delivering impressive airflow on an open bench may move much less air inside a densely packed enclosure. Conversely, a high-pressure fan is not necessarily useful if it cannot deliver sufficient airflow at the required pressure.
The essential distinction is between catalog endpoints and real operation:
- Maximum airflow occurs at zero static pressure.
- Maximum static pressure occurs at zero airflow.
- Installed airflow normally falls between these endpoints.
These maximum values are not delivered simultaneously.
The operating point is where the fan's pressure–airflow curve intersects the system-resistance curve. That intersection—not either maximum—should guide selection.

A centrifugal impeller transfers energy to the air as it moves outward. Its discharge arrangement, and housing where fitted, help develop usable pressure.
This makes centrifugal designs strong candidates when air must pass through restrictive components or change direction within equipment.
Consider a centrifugal fan for:
- Filtered enclosures with significant pressure loss.
- Heat exchangers requiring sustained airflow against resistance.
- Dense equipment with limited exhaust paths.
- Layouts needing sideways rather than straight-through discharge.
However, centrifugal fans are not immune to poor installation. Restricted inlet clearance, obstructed radial discharge, and unsuitable outlet connections can compromise performance.
Impeller design also matters. Forward-curved, backward-curved, and other centrifugal configurations do not share identical efficiency, power, or stability characteristics.
A conventional axial fan and a purpose-designed high-pressure axial fan should not be treated as equivalent.
Counter-rotating fans use two impellers rotating in opposite directions. The downstream stage can recover part of the upstream swirl and increase pressure capability.
For example, SANYO DENKI's 80 × 80 × 80 mm San Ace 80 9CRHA series includes models rated at a maximum static pressure of 2,700 Pa. Published maximum airflow is 5.65 m³/min, or 199 CFM. These remain separate curve endpoints, not a combined operating condition.

Evaluate them when:
- A straight-through airflow path must be retained.
- The chassis already uses axial fan modules.
- High component density creates substantial resistance.
- Fan depth, electrical input, and noise remain acceptable.
This is why "centrifugal always wins" is an unreliable purchasing rule. Compare specific models at the same airflow and pressure.
A meaningful comparison needs a common duty point and comparable test conditions.
Compare input power at the airflow and pressure your equipment requires. A lower-wattage fan that misses the cooling target is not an efficient solution.
Also check:
- Rated voltage and operating range.
- Startup current and available power.
- Speed-control compatibility.
- Tachometer or alarm requirements.
DC and AC describe electrical supply arrangements, not airflow geometry. Neither label alone establishes pressure capability.
Do not compare sound-pressure figures without checking measurement distance, operating speed, and test conditions.
Also evaluate installed noise. Turbulence, vibration transmission, and operation near an unstable region can change the acoustic result.
The useful question is not "Which fan type is quieter?" It is "Which suitable fan meets our cooling requirement within the noise limit?"
Use this sequence before approving a centrifugal or axial cooling fan:
1. Define the thermal requirement. Establish allowable component temperatures and the airflow needed to meet them.
2. Characterize resistance. Measure or estimate losses through filters, heat sinks, vents, and internal passages.
3. Plot the duty point. Check each candidate's pressure–airflow curve at the required supply and speed.
4. Evaluate operating changes. Include filter loading, ambient conditions, and manufacturing variation.
5. Check mechanical integration. Review inlet clearance, outlet space, sealing, and recirculation.
6. Validate the complete assembly. Measure temperatures, airflow or pressure, electrical input, and noise.
Avoid adding an arbitrary pressure margin without examining its effect on stability, energy use, and sound.
Consider an illustrative enclosure requiring 120 m³/h at 300 Pa. These figures are hypothetical, not CAPITAL test data.
One axial candidate advertises 200 m³/h maximum airflow. One centrifugal candidate advertises only 160 m³/h.
The axial fan does not automatically win. Its curve might fall below 120 m³/h at 300 Pa, while the centrifugal model might meet the requirement.
A counter-rotating axial alternative could also qualify.
Next, repeat the comparison using the expected loaded-filter resistance. A fan that meets only the clean-filter condition may lose necessary cooling airflow during service.
This two-condition assessment is more useful than ranking products by maximum airflow or maximum pressure alone.

Capital Technology Co., Limited manufactures cooling solutions under the CAPITAL brand and supplies SANYO DENKI products. Our product scope includes DC fans and AC fans.
For a targeted comparison, send your required airflow, static pressure, available dimensions, supply voltage, ambient conditions, and noise limit.
Request a duty-point comparison between centrifugal and axial candidates, supported by model-specific curves and clearly identified test conditions. This provides a stronger purchasing basis than choosing by fan category alone.
No. It is often a strong starting point, but specialized axial fans can also meet demanding pressure requirements. Compare actual curves.
Yes, provided it delivers sufficient airflow against the heat-sink and enclosure resistance. Free-air airflow alone cannot confirm suitability.
Not necessarily. Maximum pressure occurs at zero airflow. Cooling depends on useful airflow through the equipment at its operating point.
No. Series arrangements primarily increase available pressure. Actual airflow depends on the combined fan characteristic, installation, and system resistance.
No. Air bypass, recirculation, blocked vents, and poor heat transfer may remain. Evaluate the complete thermal path before replacing hardware.
1. SANYO DENKI. "Fan Air Volume and Static Pressure." Explains pressure–airflow curves, maximum ratings, operating points, and series arrangements. [Read the technical guide]. [techcompass.sanyodenki]
2. SANYO DENKI. "Centrifugal Fan Structure." Explains radial discharge, performance characteristics, and application considerations. [Read the technical guide]. [techcompass.sanyodenki]
3. SANYO DENKI. "Types of Fans." Describes axial, counter-rotating, blower, and centrifugal configurations. [Read the technical guide]. [techcompass.sanyodenki]
4. SANYO DENKI. "SANYO DENKI Develops 80 × 80 × 80 mm Counter Rotating Fan with the Highest Static Pressure in the Industry." Product announcement, May 2025; source of the cited 9CRHA specifications. [Read the product announcement]. [sanyodenki]
5. AMCA International. "Straightening Out Fan Curves." Explains duty points, pressure definitions, power curves, and system resistance. [Read the technical article]. [amca]
6. AMCA International. "Mitigating System Effect to Optimize Fan Performance and Efficiency." June 2024. Explains installation-related performance losses. [Read the technical article]. [amca]